Part List

CASAPPA

  Variable displacement axial piston pumps
Plata [LVP] Features
Variable displacement axial piston pumps swash plate design.

PLATA pumps are ideally suited for medium and high pressure open circuit applications.

Displacements from 1.75 in³/rev (28,7 cm³/rev) to 5.36 in³/rev (87,9 cm³/rev)
Max. peak pressure up to 5075 psi (350 bar)
Max. speed up to 3000 min-1

Energy saving
Low noise emission
Short response time
Drive shaft bearing suitable for radial and axial loads
Multiple combinations
MVP - MVPD Features
Variable displacement axial piston pumps swash plate design ideally suited for open circuit in mobile hydraulic applications.

The compact design allows to be mounted directly on engine motors. The new "MVPD" series allow higher flow rates than traditional pumps with the same dimension, higher machine speeds without affecting the design of the hydraulic system and a high power-to-dimension ratio.

Displacements from 0.85 in3/rev (14 cm3/rev)  to  5.17 in3/rev (84.7 cm3/rev).
Max. peak pressure up to 5075 psi  (350 bar).
Max. speed up to 3700 min-1


 
MVPD additional features
Higher speed.
Higher power -to-weight ratio.
Cost-optimized design
TVP Features
Variable displacement axial piston pumps swash plate design ideally suited for open circuit truck applications.

The compact design allows to be mounted directly on the PTOs.

Displacements from 3.66 in³/rev (60 cm³/rev) to 5.17 in³/rev (84,7 cm³/rev). 
Max. peak pressure up to 5800 psi (400 bar). 
Max. speed up to 3000 min-1

Pump internal drain line
Compensators external drain line
Direct mounting on the PTOs
Body width 4.8898 in (124,2 mm)
Compact design
Low noise emission
Plata [DVP-SVP] Features
Variable displacement axial piston pumps swash plate design for open circuit applications.

SVP single flow, DVP dual flow on piston pump and an additional piggybacked gear pump.
The automatic overall torque limiter allows to optimize the performance of the machine.
SVP and DVP pumps has been designed specifically for mini excavators where compactness and ease of installation are critical.

Piston pump: displacements from 0.48 in³/rev (7,8 cm³/rev) to 1.83 in³/rev (30 cm³/rev).
Gear pump: displacements from 0.30 in³/rev (4,95 cm³/rev) to 1.29 in³/rev (21,14 cm³/rev).
Max. speed up to 2600 min-1

Compact design
Torque limiter
Energy saving
Low noise emission
Long service life

 

Fixed displacement axial piston pumps and motors
Strada [BAP] Features
Fixed displacement bent axis piston pumps.

STRADA pumps are ideally suited for PTOs applications in vehicles.

Displacements from 2.49 in³/rev (40,9 cm³/rev) to 6.71 in³/rev (110 cm³/rev) available in groups 32 and 37.
Max. peak pressure up to 5800 psi (400 bar).
Max. speed up to 2950 min-1.

Low noise level
Direct mounting on the PTOs
Compact design
High speed
High volumetric, mechanical and overall efficiency
Available in ISO standard
Plata [LF] Features
Fixed displacement axial piston pumps and motors swash plate design for open circuit applications.

The design is extremely compact and it can integrate many functions.
An electrically controlled valve can be fitted on the pump and an electronic board controls the flow and the speed of the powered motor.

Unidirectional pumps LFP48: displacements from 1.65 in³/rev (27 cm³/rev) to 2.94 in³/rev (48,2 cm³/rev). 
 

Reversible motors LFM30: displacements from 1.34 in³/rev (22 cm³/rev) to 1.84 in³/rev (30,2 cm³/rev).

 Max. peak pressure up to 5075 psi (350 bar).

Pump
Possibility to have on the pressure line a three-position electrically controlled valve with relief valve
Possibility to mount an auxiliary gear pump with common suction
Internal drain
 

Motor
Reversible rotation with integral antishock valves
European and SAE standard mounting flanges
Side or rear inlet options
Compact size